Home | Feedback | Contact us Hello, Welcome to Jiangsu First Machinery Equpment Co.,LTD official website!
Product display
FPZ corrosion-resistant centrifugal self-priming pump

FPZ corrosion-resistant centrifugal self-priming pump

Overview: FPZ series corrosion-resistant self-priming pump is a horizontal pump with self-priming function, respectively using enhanced polypropylene RPP (-10 ℃ ~ 90 ℃) and imported fluorine resin PVDF (suitable temperature -10 ℃ ~ 120 ℃) to make. Corrosion-resistant centrifugal self-priming pump shaft seal with corrosion-resistant mechanical seal to ensure no leakage. Impeller and shaft integration, to eliminate key skidding and media intrusion into the metal shaft. Direct compact structure, high efficiency; linkage with two-stage, pump shaft assembly and disassembly. ...
Information details

FPZ corrosion-resistant centrifugal self-priming pump


FPZ corrosion-resistant centrifugal self-priming pump details:

Corrosion-resistant self-priming pump, corrosion-resistant self-priming centrifugal pump, FPZ self-priming pump

、FPZ耐腐蚀自吸泵产品概述:

该系列耐腐蚀自吸泵采用聚偏二氟乙烯(PVDF)、增强聚丙烯(RPP) -次注塑成型。机械强度高,耐腐蚀性能强,结构上有独具一格的科学性,泵腔内设有吸液室、储液室、回液止回室、气液分离室、回流孔。只需在第一次开机前灌注引液,以后不必重复灌注引液,吸入管安装液下阀,工作时机械密封不需另加冷却水冷却,操作简便、安全无泄漏,是取代液下泵的最佳产品,适用于-40°c—+120°c(PVDF)和-40°c—80°c( RPP)的各种腐蚀性介质的输送。

二、FPZ耐腐蚀自吸泵型号意义:

三、FPZ耐腐蚀自吸泵使用范围:

该耐腐蚀自吸泵适用于:化工、制药、食品、冶炼、环保、污水处理、无机盐等行业。输送液不能有泥沙或较长软纤维,以防堵塞损坏叶轮及机械密封。泵的出口应装阀门,先关阀再停机,先开机再开阀。

四、FPZ耐腐蚀自吸泵性能参数:

型号

进口×出口
mm

流量Q
m3/h

扬程H
m

转速n
r/min

吸入高度
m

电机功率
kw

25FPZ-10D

25×20

2.5

10

2840

5

0.55

32FPZ-11D

32×25

3.4

11

2840

5

0.75

40FPZ-18

40×32

11

18

2840

5

1.5

50FPZ-20

50×40

13

20

2840

5

2.2

65FPZ-25

65×50

26

25

2840

5

4

80FPZ-32

80×65

50

32

2840

5

7.5

100FPZ-40

100×80

100

20

2840

5

11

五、FPZ耐腐蚀离心式自吸泵保养及维修使用注意事项

1、使用一段时间后,发现机械密封端面泄漏,是端面磨损所致,应调整动环,放松不锈钢半圆的两颗螺钉,适当向前推进,用手旋转泵轴以轻松无阻力为佳,过松会产生泄漏,过紧易磨损影响机械密封的寿命。
2、每天连续开机8—10个小时最佳。24小时连续运转的应有备件,定期更换维修,更换期一般为二至三个月,到期都应拆下来检修。不影响生产,非连续运转生产的可随时检修。
3、输送介质比重大于1 2时应另配电机,否则将影响扬程或导致电机烧坏。
4、拆卸顺序为:卸下电机、支架、底板螺钉、卸下机械密封罩,冷却水咀、松开动环卡环螺栓,静环压板螺栓、前后泵盖螺栓,将叶轮轴拉杆紧定螺钉拧松,拧出3—5mm,用铁锤敲打拉杆,将叶轮打松后,卸下拉杆、叶轮和机械密封,在卸机械密封件时应手工操作,不可用金属工具敲打,严防损坏。
5、检修:清除泵壳、前后泵盖、叶轮、机械密封组件内的污物,并冲刷干净,无损坏的可继续使用,检查机械密封两端面有无损环,动环端面磨损或划伤较少的可用细金相砂放在平板上进行磨平,可继续使用。

六、FPZ耐腐蚀离心式自吸泵订货须知:
一、①FPZ自吸泵输送的介质②耐腐蚀自吸泵的口径③扬程需要多少(m)④流量需要多少m3/h⑤耐腐蚀自吸泵电机功率需要多少(KW)⑥泵转速(r/min)⑦电压〔V〕⑧吸程(m)⑨输送的介质温度是否需要防爆电机以便我们的为您正确选型。
二、若已经由设计单位选定我公司的产品型号,请按型号直接向我们公司销售部订购。

Popular information
Hot products
  • ZW non-blocking self-priming pump
    ZW non-blocking self-priming pump
  • ZX horizontal self-priming centrifugal pump
    ZX horizontal self-priming centrifugal pump
  • HJ stainless steel chemical process pump
    HJ stainless steel chemical process pump
  • CYZ-A self-priming pump
    CYZ-A self-priming pump
  • KCB type, 2CY gear pump
    KCB type, 2CY-type gear
  • KYB self-priming skateboard pump
    KYB self-priming skateboard pump
  • SLRP sanitary stainless steel self-priming pump
    SLRP sanitary stainless steel self-priming
  • ZXB stainless steel self-priming pump
    ZXB stainless steel self-priming pump
Top